Basic Link Aggregation scenario with high ping latency

Resume: I''m have a really basic network cenario with some new switches that I just bought. After configuring a LAG (without LACP) between them, I started to have ping losses and high

Port Aggregation FAQs

All UniFi Switches support aggregation, except USW-Flex, USW-Flex-Mini and USW-Ultra. Port aggregation is not supported on most UniFi Gateways; it is only

Configured Access List But Cannot Ping 8.8.8.8

Upon completion, I''m to access a computer on the network and ping 8.8.8.8 but this doesn''t work. I have attempted to do this multiple times over the

Unifi AP cannot ping past local switch : r/UNIFI

The AP can ping any device connected to the switch, but not past it. The AP gets DHCP, and running the ''route'' command (on the AP) outputs the same as

Troubleshooting Link Aggregation LAG/LACP Not Working

This Article Applies to: Omada switch with Static LAG and LACP supported. Issue Description: Static LAG or LACP does not link up or aggregate the speed. Troubleshooting: When

Difference between an access switch and aggregation switch?

Hi There, I would like to know what the difference is between the access switches and an aggregation switch. We are looking at a environment where we are quoting on 2 x MS225-48LP

Can''t ping L3 switch without enabling routing for interface

This may be a dumb question but can someone please explain to me why I cannot ping a L3 switch with an IP address assigned to it without enabling routing for the default vlan interface? It''s

Back Button

Hier sollte eine Beschreibung angezeigt werden, diese Seite lässt dies jedoch nicht zu.

Can''t Access Switch GUI, but I can ping it. : r/networking

Hello, we are configuring a remote site of about 10 switches, Netgear M4300''s. The management IP was already set on one switch, but the GUI will not pull up. I can ping the management interface from all

Case Study: An Access Switch Cannot Ping the Gateway When the

Figure 15-11 Networking diagram for the failure of an access switch to ping the gateway when the uplink and downlink interfaces of the aggregation switch are bundled into Eth-Trunks respectively. SwitchB

Core to access switch ping working and access to core is not pinging

how is your routing configured on Core and Access switch ? Look for me Access switch do not aware the IP coming from Core switch to reach back. so make sure Access switch aware

What Is an Aggregation Switch and How to Choose?

Discover the role of aggregation switches. Explore differences between aggregation, access, and core switches, and choose the right model

Device Cannot Ping Gateway

To ensure that RSTP or MSTP on Ruijie switches and H3C switches are compatible, you need to configure the packet format on H3C switch interfaces

Switch is working but will not ping?

Once all the changes had been saved, the switch & pc ip addresses were now able to be pinged. However, back in the office (15mins later) pings have stopped to the switch but not to the pc

Port Aggregation Configurations

Port Aggregation Port aggregation allows you to group multiple physical ports into one unit. Port aggregation is useful for implementing load balancing and provides a redundant link backup. To

I cannot get my Mikrotik switches to ping the router or connect to

I have 3 Mikrotik switches (a CRS310, CRS312, & CRS326) and none of them are accessible via the IP address I''ve given them, nor can they ping out to the OPNSense router that I

Troubleshooting Link Aggregation LAG/LACP Not Working

Troubleshooting: When LACP (Link Aggregation Control Protocol) or static LAG (Link Aggregation Group) is not functioning properly, common troubleshooting steps and checkpoints

forum.huawei.com

Huawei support community is a communication center for sharing experiences and knowledge, solving questions and problems for enterprise partners, customers and engineers.

Can''t Access Switch GUI, but I can ping it. : r/networking

The management IP was already set on one switch, but the GUI will not pull up. I can ping the management interface from all the other switches, as well as the computer in the same rack.

Troubleshooting Tip: FortiLink aggregate interface is down, causing

fortilink is not up, please check physical connection. Under Network -> Interface, try disabling and re-enabling the FortiLink interface. Note: After the FortiGate device is upgraded from

Can Access Internet but Can''t Ping 8.8.8.8

Hello, I am using a Cisco 9300 switch with computers plugged into it via ethernet. The devices can access the internet and ping 1.1.1.1, but cannot

Ping not working in HPE Aruba 2930F with Openflow aggregate mode

I have an HPE Aruba 2930F JL259A switch which is used to try out SDN related experiments. But after the aggregate mode instance is enabled, the ping command does not work.

Unifi Aggregation switch and Ping Test with Fiber/DAC

Everything connected to the A switch is connected at 10G automatically. When I ping the Aggregation switch or from the A switch to any other device, including the UXG Pro, which is directly connected

Case Study: An Access Device Cannot Ping the Gateway When the

In this case, DeviceB cannot ping DeviceC. Figure 8-11 Networking diagram for the failure of an access device to ping the gateway when the uplink and downlink interfaces of the aggregation device are

What to check if ''pinging'' doesn''t work?

What would be the preliminary checks that should be carried out if a server cannot ''ping''?

Solved: LIVEcommunity

I have configured 2 aggregate (L3 trunk) interfaces and added sub interfaces to these aggregate. The first problem is the firewall itself can not ping directly connected device by using "ping

Switch cannot ping server

My switch won''t ping my server. Both are directly connected with each other, and are in vlan 666. When I initiate a ping from my switch to my server, the switch sends ARP requests. Then the server